Choose a rail connector from the joint geometry
A rail connector must match more than the direction of travel. Straight and angled joints depend on the rail profile, outside and inside dimensions, wall thickness, actual angle, visible-joint preference and final fixing method. Use the current product routes below to describe the joint, then require the proposed connector geometry to be shown against the rail section.
Discuss a rail joint on WhatsApp
Five current product routes
Use as a review route when a general or mixed rail-joint problem does not yet fit another family. “Universal” does not prove fit with every tube profile, size, wall thickness or fixing method.
Use for a specified right-angle route. Confirm whether the angle refers to rail centre-lines or end faces, plus profile, bend/corner envelope and visible joint treatment.
Use when the project drawing calls for this angled transition. The product name is a route; verify the actual geometry, orientation and interface before ordering.
Use to continue two aligned rail sections. Provide the actual section and whether the joint is internal, external, visible, concealed, welded or mechanically retained.
Use for a defined variable or non-standard set angle. Confirm whether adjustment is only during installation, the permitted range and the final locked condition; do not infer movement in service.
Define six joint fields before comparing connectors
Field — Provide — Why it matters
Rail profile — Round, square, rectangular or custom cross-section with dimensions — Connector geometry must seat inside, around or against that exact profile.
Inside fit — Inside dimensions, wall thickness, seams and corner radii where an internal connector is considered — Equal outside sizes do not guarantee equal internal space or insertion fit.
Direction and angle — Plan/elevation sketch with actual centre-line directions — It distinguishes straight, fixed-corner and variable-angle routes and prevents mirrored or rotated mismatches.
Joint appearance — Visible connector, concealed insert, weld-finished joint or another defined outcome — It changes connector type, site work, surface finishing and inspection access.
Retention method — Permitted weld, screw/pin, clamp or another project-specified method — A connector body is incomplete without an agreed way to keep the joint in its final position.
Support and route — Nearest brackets/posts, rail function, section lengths and installation sequence — Joint location and assembly access must suit the complete supported rail route.
Quick routing examples
• Two cut sections continue on one axis: start with Straight Rail Joiners and provide the rail cross-section plus desired joint visibility.
• A balcony rail turns a true right angle: start with 90 Degree Rail Corners and show the available corner envelope and route orientation.
• A landing or layout uses a specified oblique turn: start with 135 Degree Corner Connectors only when that geometry matches the drawing; otherwise request an angle-specific review.
• The angle is set on site: start with Flexible Rail Connectors and state the required range, set angle, access and final locking method.
Do not place a joint only where stock lengths happen to end. The project team should review support locations, route continuity, fabrication, installation sequence and any code or structural responsibility for the complete rail assembly.
What the proposed configuration should state
• current product route and connector drawing or marked dimensions;
• matching rail profile, relevant outside/inside dimensions and wall thickness;
• joint angle and orientation, with clear reference points;
• internal/external and visible/concealed relationship;
• retention or welding method, included fasteners and required site work;
• proposed material grade, finish, quantity and packaging basis;
• open dimensions and system checks that remain before production.
A rail offcut photo beside a dimensioned sketch can start route selection. A final fit still requires the actual cross-section and joint geometry.
Choose between level, raked, and raked-to-level mesh panel geometry by railing run, pattern orientation, interfaces, and project drawings.
Specify handrail sleeves and splice locks by the actual tube interior, required retention and installation access so the connector can fit and be secured.
Zorg ervoor dat verbindingspunten worden voorzien van steunen, overgangen en toegangsmogelijkheden voor montage, zodat de breekpunten voor het transport ook fungeren als gedocumenteerde verbindingen in de geïnstalleerde leuning.
Connect the usable rail path with joint function, supports, movement and transport modules before issuing a continuous handrail specification.
Send coordinated run drawings, substrate details, finish references and scope requirements so surface-mount handrail quotes can be compared meaningfully.
Leg de bestaande ondergrond, de toestand van de randen, de afwerkingen, verborgen leidingen en installaties, de toegankelijkheid, de geometrie en de omvang van de reparatiewerkzaamheden vast voordat met de fabricage voor de aanpassing wordt begonnen.


Foshan ESANG Metal Products onderhoudt met trots CE-certificering (Verificatienummer TD32772401) onder de Richtlijn bouwproducten (Verordening nr. 305/2011), waarmee we onze toewijding aan de hoogste Europese veiligheids- en kwaliteitsnormen bevestigen.
Gecertificeerd Assortiment:
Ons uitgebreide assortiment railingbeslag - inclusief glasklemmen, spanners, beugels, muurbevestigingen, basischoenen, leuningbeslag, kabelbeslag en staanderonderdelen - voldoet aan de volgende eisen EN1906:2012 normen, zodat de structurele integriteit en betrouwbaarheid van de prestaties in alle installaties gewaarborgd zijn.
Wat dit betekent voor je project:
✓ Volledige naleving van regelgeving voor Europese en internationale markten
✓ Onafhankelijk geverifieerde veiligheids- en duurzaamheidsprestaties
✓ Documentatie-ondersteuning voor architecturale specificaties
Gemoedsrust dankzij kwaliteitsgarantie van derden
Certificering geldig tot 2027 | Testrapport: CE-FE24122001-CY

