Railingsystemen voor binnen

Railingsystemen voor binnen

Use this category to turn an interior stair, corridor, atrium, mezzanine or balcony-edge brief into a defined railing route. Start with the user task and surrounding construction, then select the handrail or guard arrangement, infill, visible finish and fixing interface. An indoor location does not automatically make a system accessible, code-compliant or suitable for every cleaning regime.

Discuss an indoor railing requirement

Route the project by its real indoor task

• Interior Stair Railings 304 — for sloped runs where stair geometry, support method, handrail continuity, transitions and terminations drive the component set. The title’s grade is not a substitute for the project material specification.

• Interior Balcony Railings 304 — for atriums, mezzanines and internal edges where the guard layout, post or channel support, infill and floor-edge interface must be coordinated.

• Modern Interior Systems — when the purchasing task begins with a glass, cable, slim-profile or reduced-visible-hardware design direction and needs compatible components rather than a style label alone.

• Commercial Interior Rails — for repeated public or commercial areas where consistent interfaces, replaceable parts, cleaning access, finish control and packaging by area are important.

• ADA Compliant Interior Systems — an existing route for projects with an explicit accessibility brief. Provide the governing jurisdiction, route drawings and required dimensions; the page name does not certify a component or the installed system as compliant.

Choose the system before the finish

Wall-supported handrail

This route is appropriate when hand support is required along a wall and no guard infill is being purchased. Confirm wall construction and backing, rail profile, support locations, projection, inside and outside corners, returns, transitions and the party responsible for wall anchors. A bracket cannot be selected from rail diameter alone if the mounting surface and required clearances are unknown.

Post-supported handrail or guard

Use a post route where the assembly is fixed to a floor, stair, stringer or edge rather than a continuous supporting wall. Define post spacing, rail geometry, base or side fixing, infill and the exposed floor build-up. The finished flooring, tile, stone or screed is not automatically a structural anchoring substrate.

Glass, cable or other infill

Glass routes need the panel build-up, edge treatment, holes if any, joint layout and proposed support method. Cable routes need post and terminal locations, corner changes, cable construction and project-set spacing. Bar, mesh or custom-panel routes require the infill geometry and attachment concept. Do not combine a visually preferred infill with unrelated posts or fittings before their interfaces are checked.

Coordinate the building and adjacent trades

• Walls: identify concrete, masonry, stud framing, lining and known backing. The wall trade or project engineer should confirm that the receiving construction can take the proposed fixing.

• Floors and edges: record slab or steel edge geometry, finishes, steps, nosings, joints and any concealed services. Anchor design and drilling zones belong with the structural and site team unless specifically included.

• Glass: state whether glass is in ESANG’s requested supply or by another trade, and coordinate panel sizes, holes, tolerances and hardware contact details.

• Joinery and finishes: allow for wall panels, skirtings, flooring, paint and decorative metalwork so brackets, base covers and returns do not clash.

• Accessibility and local requirements: provide the actual project criteria. Manufacturing to supplied dimensions does not transfer design, approval or final compliance responsibility.

Indoor does not always mean dry or mild. Pools, spas, wet-cleaned areas, food-service zones and chemical exposure should be declared because they may change the material, finish, fasteners and maintenance plan.

Send enough information to compare proposals

A sketch and site photos are enough to begin. Include the building use, route type, approximate runs, stair pitch or edge geometry, wall/floor construction, preferred handrail and infill, finish direction, estimated quantity, target specification and any accessibility brief.

Ask the quotation to identify the included component groups, material and finish by component, mating dimensions, proposed mounting route, loose fasteners if included, glass or cable interfaces, items by others, and the drawings or approvals required before production. This makes a wall-handrail proposal comparable with another wall-handrail proposal instead of mixing it with a guard or infill package.

Send indoor drawings or photos on WhatsApp

Gerelateerde berichten:

Esangs projecten

Esang's certificaat

Foshan ESANG Metal Products onderhoudt met trots CE-certificering (Verificatienummer TD32772401) onder de Richtlijn bouwproducten (Verordening nr. 305/2011), waarmee we onze toewijding aan de hoogste Europese veiligheids- en kwaliteitsnormen bevestigen.

Gecertificeerd Assortiment:
Ons uitgebreide assortiment railingbeslag - inclusief glasklemmen, spanners, beugels, muurbevestigingen, basischoenen, leuningbeslag, kabelbeslag en staanderonderdelen - voldoet aan de volgende eisen EN1906:2012 normen, zodat de structurele integriteit en betrouwbaarheid van de prestaties in alle installaties gewaarborgd zijn.

Wat dit betekent voor je project:

  • ✓ Volledige naleving van regelgeving voor Europese en internationale markten

  • ✓ Onafhankelijk geverifieerde veiligheids- en duurzaamheidsprestaties

  • ✓ Documentatie-ondersteuning voor architecturale specificaties

  • Gemoedsrust dankzij kwaliteitsgarantie van derden

Certificering geldig tot 2027 | Testrapport: CE-FE24122001-CY

Esangs projecten

Neem nu contact met ons op!