Glass clamps are a useful route when a panel must connect to a post, wall or other support at discrete points rather than sit in a continuous base channel. Start with the support geometry and the glass preparation, not the clamp’s front shape alone. A useful request can begin with a photo, a panel sketch and an estimated quantity; ESANG can then identify a proposed clamp configuration for comparison.
Discuss your glass clamp requirement on WhatsApp
Choose the product route by the connection problem
Product route — Use it to start this comparison — Do not decide it from appearance alone
Ronde glasklemmen — A circular clamp body is part of the required visual or hardware language. — Confirm the rear mounting face, support profile, glass interface and fastener access.
Vierkante glasklemmen — A square or rectangular face is preferred for a linear railing layout. — Confirm whether the back must fit a flat, round or project-specific support.
Verstelbare glasklemmen — The panel angle, alignment or site tolerance calls for a defined adjustment function. — Ask the proposal to state what adjusts, the usable range and how the final position is locked.
Mini glasklemmen — Reduced visual mass or limited space is a priority. — A smaller body is not evidence of suitability; panel size, support layout and project loads still govern.
Zware glasklemmen — The project has more demanding panel, use or exposure conditions and needs a reviewed connection. — “Heavy duty” is not a load value. Require the proposed item, test basis and complete installation condition to be identified.
What the current product photos can and cannot show
Lock the interfaces before glass is released
Glass side
State the glass build-up, nominal thickness, panel width and height, edge condition and whether holes or notches are already defined. The proposal should identify the contact parts, liners or gaskets, required glass preparation and any position dimensions that the glass fabricator must follow. Do not assume a product shown with a liner is suitable for every glass build-up.
Support side
Show whether the clamp meets a round post, square post, rectangular member, wall, fascia or fabricated plate. Give the relevant support dimensions and available access for tools and fasteners. The front face may stay the same while the rear interface changes; that hidden interface is often where otherwise similar-looking clamps stop being interchangeable.
System responsibility
A clamp is one connection within a glass barrier. Panel size, support spacing, post or wall strength, fasteners, edge distances and installation all affect the result. If a project has required loads or a named standard, send that requirement and ask for the exact proposed hardware and supporting documentation. Do not substitute a category label, material name or product photo for complete-system review.
Compare quotations on the same fields
• Product route and proposed clamp form, with a photo or drawing that identifies the exact item.
• Glass build-up and preparation the proposal is based on.
• Rear mounting geometry, mating support dimensions and hole or fastener pattern.
• Included liners, pins, screws and other contact parts; anchors or support fabrication should be listed separately.
• Proposed material and finish, with exposure conditions stated by the buyer rather than inferred from the image.
• Quantity, packaging, marking and any inspection or documentation requirements.
Start with the information you already have
Send a drawing if one exists. If not, send a clear support photo, glass thickness, approximate panel size, indoor or outdoor exposure, desired clamp appearance and estimated quantity. ESANG’s response should turn that starting information into a proposed configuration and a short list of unresolved dimensions, without treating every researched option as automatically available.
Choose between level, raked, and raked-to-level mesh panel geometry by railing run, pattern orientation, interfaces, and project drawings.
Specify handrail sleeves and splice locks by the actual tube interior, required retention and installation access so the connector can fit and be secured.
Zorg ervoor dat verbindingspunten worden voorzien van steunen, overgangen en toegangsmogelijkheden voor montage, zodat de breekpunten voor het transport ook fungeren als gedocumenteerde verbindingen in de geïnstalleerde leuning.
Connect the usable rail path with joint function, supports, movement and transport modules before issuing a continuous handrail specification.
Send coordinated run drawings, substrate details, finish references and scope requirements so surface-mount handrail quotes can be compared meaningfully.
Leg de bestaande ondergrond, de toestand van de randen, de afwerkingen, verborgen leidingen en installaties, de toegankelijkheid, de geometrie en de omvang van de reparatiewerkzaamheden vast voordat met de fabricage voor de aanpassing wordt begonnen.


Foshan ESANG Metal Products onderhoudt met trots CE-certificering (Verificatienummer TD32772401) onder de Richtlijn bouwproducten (Verordening nr. 305/2011), waarmee we onze toewijding aan de hoogste Europese veiligheids- en kwaliteitsnormen bevestigen.
Gecertificeerd Assortiment:
Ons uitgebreide assortiment railingbeslag - inclusief glasklemmen, spanners, beugels, muurbevestigingen, basischoenen, leuningbeslag, kabelbeslag en staanderonderdelen - voldoet aan de volgende eisen EN1906:2012 normen, zodat de structurele integriteit en betrouwbaarheid van de prestaties in alle installaties gewaarborgd zijn.
Wat dit betekent voor je project:
✓ Volledige naleving van regelgeving voor Europese en internationale markten
✓ Onafhankelijk geverifieerde veiligheids- en duurzaamheidsprestaties
✓ Documentatie-ondersteuning voor architecturale specificaties
Gemoedsrust dankzij kwaliteitsgarantie van derden
Certificering geldig tot 2027 | Testrapport: CE-FE24122001-CY

