Conectores de carril

Conectores de carril

Choose a rail connector from the joint geometry

A rail connector must match more than the direction of travel. Straight and angled joints depend on the rail profile, outside and inside dimensions, wall thickness, actual angle, visible-joint preference and final fixing method. Use the current product routes below to describe the joint, then require the proposed connector geometry to be shown against the rail section.

Discuss a rail joint on WhatsApp

Five current product routes

Conectores universales para raíles

Use as a review route when a general or mixed rail-joint problem does not yet fit another family. “Universal” does not prove fit with every tube profile, size, wall thickness or fixing method.

Esquinas de carril de 90 grados

Use for a specified right-angle route. Confirm whether the angle refers to rail centre-lines or end faces, plus profile, bend/corner envelope and visible joint treatment.

Conectores de esquina de 135 grados

Use when the project drawing calls for this angled transition. The product name is a route; verify the actual geometry, orientation and interface before ordering.

Uniones rectas para rieles

Use to continue two aligned rail sections. Provide the actual section and whether the joint is internal, external, visible, concealed, welded or mechanically retained.

Conectores ferroviarios flexibles

Use for a defined variable or non-standard set angle. Confirm whether adjustment is only during installation, the permitted range and the final locked condition; do not infer movement in service.

Define six joint fields before comparing connectors

Field — Provide — Why it matters

Rail profile — Round, square, rectangular or custom cross-section with dimensions — Connector geometry must seat inside, around or against that exact profile.

Inside fit — Inside dimensions, wall thickness, seams and corner radii where an internal connector is considered — Equal outside sizes do not guarantee equal internal space or insertion fit.

Direction and angle — Plan/elevation sketch with actual centre-line directions — It distinguishes straight, fixed-corner and variable-angle routes and prevents mirrored or rotated mismatches.

Joint appearance — Visible connector, concealed insert, weld-finished joint or another defined outcome — It changes connector type, site work, surface finishing and inspection access.

Retention method — Permitted weld, screw/pin, clamp or another project-specified method — A connector body is incomplete without an agreed way to keep the joint in its final position.

Support and route — Nearest brackets/posts, rail function, section lengths and installation sequence — Joint location and assembly access must suit the complete supported rail route.

Quick routing examples

• Two cut sections continue on one axis: start with Straight Rail Joiners and provide the rail cross-section plus desired joint visibility.

• A balcony rail turns a true right angle: start with 90 Degree Rail Corners and show the available corner envelope and route orientation.

• A landing or layout uses a specified oblique turn: start with 135 Degree Corner Connectors only when that geometry matches the drawing; otherwise request an angle-specific review.

• The angle is set on site: start with Flexible Rail Connectors and state the required range, set angle, access and final locking method.

Do not place a joint only where stock lengths happen to end. The project team should review support locations, route continuity, fabrication, installation sequence and any code or structural responsibility for the complete rail assembly.

What the proposed configuration should state

• current product route and connector drawing or marked dimensions;

• matching rail profile, relevant outside/inside dimensions and wall thickness;

• joint angle and orientation, with clear reference points;

• internal/external and visible/concealed relationship;

• retention or welding method, included fasteners and required site work;

• proposed material grade, finish, quantity and packaging basis;

• open dimensions and system checks that remain before production.

A rail offcut photo beside a dimensioned sketch can start route selection. A final fit still requires the actual cross-section and joint geometry.

Send the rail-joint details on WhatsApp

Related Posts:

Proyectos de Esang

Certificado de Esang

Foshan ESANG Metal Products se enorgullece de mantener Certificación CE (Verificación n.º TD32772401) en virtud de la Directiva sobre productos de construcción (Reglamento n.º 305/2011), lo que afirma nuestro compromiso con los más altos estándares europeos de seguridad y calidad.

Gama de productos certificados:
Nuestra amplia gama de herrajes para barandillas, que incluye abrazaderas de vidrio, tensores, soportes, soportes de pared, zapatas, herrajes para pasamanos, herrajes para cables y componentes para postes, satisface los requisitos más exigentes. EN1906:2012 garantizando la integridad estructural y la fiabilidad del rendimiento en todas las instalaciones.

Qué significa esto para su proyecto:

  • ✓ Cumplimiento total de la normativa para los mercados europeos e internacionales

  • ✓ Rendimiento de seguridad y durabilidad verificado de forma independiente.

  • ✓ Soporte de documentación para las especificaciones arquitectónicas

  • ✓ Tranquilidad gracias a la garantía de calidad de terceros

Certificación válida hasta 2027 | Informe de pruebas: CE-FE24122001-CY

Proyectos de Esang

Póngase en contacto con nosotros