Paalkappen & eindkappen (rond, vierkant, decoratief)

Twee gepolijste, vierkante metalen paalkappen met daarop bijpassende bollen

Post caps close the top of vertical posts; end caps close open horizontal rails or tube ends. Round, square, flat, domed and decorative profiles can look similar in a photograph but require different mating dimensions and retention. Send the tube outside and inside dimensions, wall thickness, end orientation, finish and approximate quantity so ESANG can identify a proposed cap for review.

Ask about post and end caps on WhatsApp

Match the cap to the tube, not the nominal name

"Two-inch," "50 mm," round and square descriptions are not enough to freeze a fit. State whether the cap goes over the outside of the tube, plugs into the bore or meets the end as a weld-on piece. Then provide:

  • round outside diameter, or square/rectangular outside dimensions;
  • inside dimension or actual wall thickness at the end;
  • end squareness, corner radius and any weld seam or burr that affects insertion;
  • vertical post top, horizontal rail end or another orientation;
  • required visible profile: flat, domed, ball, stepped or other decorative form.

A cap sized by outside dimension may not fit an internal bore, and an insert sized for one wall thickness can be loose or impossible to install in another. If the tube is already on site, include calliper measurements and clear end photographs rather than relying only on a drawing title.

Assortment of round flat and domed caps with several square flat caps
The assortment shows visible differences in shape and size. It is not a fixed catalogue range and does not establish material, fit or current availability.

Choose a retention method that can be inspected

Common cap concepts in the market include drive-on or press-fit shells, internal plugs, weld-on caps, screw-fixed caps and bonded caps. These are requests a buyer may make, not a promise that every method is available for every profile. The quotation should state the proposed retention method, mating dimensions, installation access and any consumable or fastener included.

  • Drive-on or press-fit: needs a defined interference and controlled tube tolerances; excessive force can distort thin tube or damage the finish.
  • Weld-on: needs joint preparation, compatible material, a finish-restoration plan and site or factory welding responsibility.
  • Screw-fixed: needs screw position, edge clearance, access and a decision about whether the fastener remains visible.
  • Bonded: needs a specified adhesive compatible with the materials, exposure, gap and installation conditions; adhesive choice should not be guessed from appearance.
Round flat, domed and ball-shaped end pieces in several visible sizes, including pieces with centre openings
Some pieces are closed while others have centre openings. The required passage, plug or decorative-only role must be stated; the image does not prove internal construction.

Decorative caps are not structural connectors

A ball, dome or shaped finial can finish a post and reduce exposure of the open tube. Unless a reviewed design explicitly assigns another function, it should not be treated as a handhold, tie-off point, anchor, top-rail splice or load-bearing fitting. A centre opening may be for another component, but its purpose cannot be inferred from the photograph.

If the cap carries lighting, signage, a rail extension or another attachment, describe that separately and provide the required interface and loads. The resulting assembly may need a different internal connector rather than a decorative shell.

Coordinate exposure, water and finish

For exterior posts, identify whether the cap is expected to shed water, seal an opening or leave a drainage route elsewhere. A cap is not automatically watertight. Temperature change, trapped moisture and cleaning chemicals can affect the tube-cap joint. Coastal, pool and industrial locations also require the proposed cap, fastener, weld and post materials to be considered together.

State the required visible finish and direction. A polished photograph does not prove the base alloy, and a finish name does not guarantee a colour match between production batches. If a match to existing rails is important, request a physical sample or agreed finish reference before the full quantity is released.

Make the quotation a usable cap schedule

  • cap use: vertical post top, horizontal rail end or decorative finial;
  • round, square or rectangular mating profile and actual dimensions;
  • over-cap, insert or weld-on fit, plus engagement depth;
  • retention method, included fastener or consumable, and installation responsibility;
  • open or closed form, water-management expectation and any centre opening;
  • proposed material, finish and requested sample or material record;
  • quantity by size and shape, packing separation and drawing revision.

You can begin with a photograph and estimated quantity. Before production, provide actual tube measurements, end condition, exposure, finish, retention preference and any attached component. ESANG’s quotation should list the proposed shapes and sizes; it should not imply that every form in the public photographs is part of one current supply range.

Send your cap schedule on WhatsApp

Gerelateerde berichten:

Afbeelding van Ivy Wang

Ivy Wang

Ivy Wang is technisch schrijver en productspecialist bij esang.co met 6 jaar ervaring in roestvrijstalen railingsystemen. Op haar 29e heeft ze gewerkt aan meer dan 200 hardware op maat projecten, het helpen van klanten navigeren alles van marine-grade installaties tot commerciële compliance-eisen. Ivy's aanpak is gericht op praktische, klantgerichte oplossingen in plaats van aanbevelingen die voor iedereen gelden. Ze is gespecialiseerd in het vertalen van complexe technische specificaties naar bruikbaar advies voor architecten, aannemers en huiseigenaren.

Neem nu contact met ons op!