Glass clamps are a useful route when a panel must connect to a post, wall or other support at discrete points rather than sit in a continuous base channel. Start with the support geometry and the glass preparation, not the clamp’s front shape alone. A useful request can begin with a photo, a panel sketch and an estimated quantity; ESANG can then identify a proposed clamp configuration for comparison.
Discuss your glass clamp requirement on WhatsApp
Choose the product route by the connection problem
Product route — Use it to start this comparison — Do not decide it from appearance alone
Круглые стеклянные зажимы — A circular clamp body is part of the required visual or hardware language. — Confirm the rear mounting face, support profile, glass interface and fastener access.
Квадратные стеклянные зажимы — A square or rectangular face is preferred for a linear railing layout. — Confirm whether the back must fit a flat, round or project-specific support.
Регулируемые зажимы для стекла — The panel angle, alignment or site tolerance calls for a defined adjustment function. — Ask the proposal to state what adjusts, the usable range and how the final position is locked.
Мини-зажимы для стекла — Reduced visual mass or limited space is a priority. — A smaller body is not evidence of suitability; panel size, support layout and project loads still govern.
Прочные зажимы для стекла — The project has more demanding panel, use or exposure conditions and needs a reviewed connection. — “Heavy duty” is not a load value. Require the proposed item, test basis and complete installation condition to be identified.
What the current product photos can and cannot show
Lock the interfaces before glass is released
Glass side
State the glass build-up, nominal thickness, panel width and height, edge condition and whether holes or notches are already defined. The proposal should identify the contact parts, liners or gaskets, required glass preparation and any position dimensions that the glass fabricator must follow. Do not assume a product shown with a liner is suitable for every glass build-up.
Support side
Show whether the clamp meets a round post, square post, rectangular member, wall, fascia or fabricated plate. Give the relevant support dimensions and available access for tools and fasteners. The front face may stay the same while the rear interface changes; that hidden interface is often where otherwise similar-looking clamps stop being interchangeable.
System responsibility
A clamp is one connection within a glass barrier. Panel size, support spacing, post or wall strength, fasteners, edge distances and installation all affect the result. If a project has required loads or a named standard, send that requirement and ask for the exact proposed hardware and supporting documentation. Do not substitute a category label, material name or product photo for complete-system review.
Compare quotations on the same fields
• Product route and proposed clamp form, with a photo or drawing that identifies the exact item.
• Glass build-up and preparation the proposal is based on.
• Rear mounting geometry, mating support dimensions and hole or fastener pattern.
• Included liners, pins, screws and other contact parts; anchors or support fabrication should be listed separately.
• Proposed material and finish, with exposure conditions stated by the buyer rather than inferred from the image.
• Quantity, packaging, marking and any inspection or documentation requirements.
Start with the information you already have
Send a drawing if one exists. If not, send a clear support photo, glass thickness, approximate panel size, indoor or outdoor exposure, desired clamp appearance and estimated quantity. ESANG’s response should turn that starting information into a proposed configuration and a short list of unresolved dimensions, without treating every researched option as automatically available.
Distinguish handrail returns, end caps and unresolved end interfaces, then schedule each termination by function, adjoining construction and supply responsibility.
Choose factory-cut or site-trimmed handrails by checking dimension status, datums, mating allowances and the finish work attached to each cut.
Compare tube-only and component-package handrail quotes by separating fittings, fabrication, mounting interfaces, finish work and delivered quantities.
Compare continuous and sectional handrail supply using delivery access, joint locations, mating details and section identification before fabrication release.
Choose a handrail support change by comparing wall and post interfaces, preserving the gripping path and locating the transition on coordinated drawings.
Выберите одну из следующих геометрий сетчатых панелей: ровная, наклонная или наклонная с переходом в ровную — в зависимости от участка ограждения, ориентации узора, соединительных элементов и проектных чертежей.


Компания Foshan ESANG Metal Products с гордостью поддерживает сертификация CE (Верификационный номер TD32772401) в соответствии с Директивой о строительной продукции (Постановление № 305/2011), что подтверждает нашу приверженность высочайшим европейским стандартам безопасности и качества.
Сертифицированный ассортимент продукции:
Наш обширный ассортимент фурнитуры для перил, включающий зажимы для стекла, натяжители, кронштейны, настенные крепления, опорные башмаки, фурнитуру для перил, кабельное оборудование и компоненты для столбов, отвечает требованиям EN1906:2012 стандарты, обеспечивающие целостность конструкции и надежность работы всех установок.
Что это значит для вашего проекта:
✓ Полное соответствие нормативным требованиям для европейского и международного рынков
✓ Независимая проверка безопасности и долговечности
✓ Документационная поддержка архитектурных спецификаций
✓ Гарантия качества от третьей стороны
Сертификация действительна до 2027 года | Отчет об испытаниях: CE-FE24122001-CY

