Glass railing hardware is a component-selection task, not a single interchangeable kit. Use this directory to route a requirement by how the glass is supported, where it is installed, which interfaces remain visible, and who is responsible for the glass, structure, anchors, waterproofing, and installation. ESANG can review component or batch requirements from drawings, schedules, samples, or an annotated site photo; the proposed supply should then be frozen in a written quotation.
Send your glass railing hardware requirement on WhatsApp
Choose the hardware family by support strategy
Clamps and connectors for post- or surface-supported glass
玻璃夹具和连接器 are the first route when panels attach to posts, tubes, walls, or another prepared face. Freeze the glass build-up and thickness, the flat or curved mounting face, the gasket or liner, any pin or glass-hole requirement, and the fastener interface. A clamp that matches the visible shape can still be wrong for the glass preparation or backing geometry. Use the family page to compare real entries such as 可调节玻璃夹 和 Round Glass Clamps 304/316; their names do not make either option universally compatible.
Spigots and standoffs for bottom or side point support
玻璃拉钉和支座 contains two different routing directions. Spigots support glass from below and must be coordinated with the surface or prepared core location. Standoffs hold drilled glass away from a wall, fascia, or stair stringer and require the projection, hole pattern, edge distances, and backing condition. Compare 表面安装式玻璃接头, 玻璃芯钻接头, ,以及 可调节玻璃间隔柱 according to the actual support position rather than the desired frameless appearance alone.
Base shoe systems for continuous bottom support
底鞋系统 route projects that require a continuous lower support line instead of individual point supports. The quotation should identify the load-bearing profile, glass retention parts, gaskets, covers, end conditions, drainage provision, joints, and the proposed interface to the substrate. Surface-mounted, recessed, and flush-looking details are not interchangeable. The catalog currently includes 玻璃底鞋槽, 嵌入式玻璃导轨, and related profile entries; the exact section and supply composition must be confirmed for the project.
Brackets and adapters for local transitions
玻璃支架和适配器 route local connections between glass and a wall, post, support plate, or another prepared member. Begin with the support-face drawing, glass hole or edge detail, projection, orientation, adjacent component, and accessible fastener space. Wall to Glass Connectors 和 Post to Glass Adapters identify different receiving conditions; neither product title confirms the substrate, anchors, or structural capacity.
Cap rails for the upper edge and visible finish
盖栏 route requirements for a continuous upper profile, a protected glass edge, or a defined top-line appearance. Confirm the glass build-up, liner or bonding interface, profile shape, straight and corner joints, ends, surface finish, and relationship to any required graspable handrail. A cap rail does not replace the glass support below unless the complete design specifically assigns and verifies that role. Real entries include 连续盖板系统 和 结构性玻璃槽钢.
Five decisions that prevent category-level mismatches
1. Define the glass before matching hardware
State the glass type and build-up, nominal thickness, panel height and width, edge treatment, holes, notches, corner work, and available fabrication tolerances. The glass supplier or project designer should confirm glass machining before production. Do not use the hardware photograph or a previous project as the machining drawing.
2. Identify the support path
Mark whether the panel is retained between posts, supported at bottom points, offset from a side structure, held continuously in a base shoe, connected by local brackets, or finished with a top profile. If more than one family is used, show where each begins and ends. The project engineer remains responsible for the complete load path and the installed-system design.
3. Record the installation position and substrate
Distinguish top mounting, core drilling, side or fascia mounting, wall mounting, post mounting, and continuous channel mounting. Provide the substrate material and build-up, finished levels, edge distances, waterproofing zones, drainage path, and anchor restrictions. Hardware selection cannot resolve an unknown or unsuitable substrate.
4. Separate visible finish from technical fit
Record round or square geometry, exposed cover details, the required material grade, finish direction, polish level or project color, and adjacent metal finishes. Exposure to interiors, weather, pool chemicals, salt, cleaning products, and dissimilar metals affects the specification. A similar-looking surface does not prove the material, corrosion suitability, or compatibility.
5. Assign site and supply responsibilities
Identify who specifies and supplies the glass, structural backing, anchors, gaskets or liners, sealants, drainage parts, waterproofing, adjacent rails or posts, installation, inspection, and engineering review. Ask for the quotation and drawing review to state ESANG’s proposed hardware, included accessories, exclusions, and interfaces rather than assuming a complete installed system.
Common interfaces to freeze in the quotation
• Glass to hardware: glass build-up, thickness tolerance, slot or contact geometry, gaskets or liners, holes, notches, edge distances, and tightening or retention method.
• Hardware to support: post or tube profile, wall or fascia build-up, base plate or embedded detail, anchor pattern, edge clearance, access for installation, and substrate verification.
• Component to component: mating diameters or sections, straight and corner joints, rail ends, cover pieces, fasteners, finish alignment, and any interfaces with posts, handrails, or other packages.
• Exposure and maintenance: indoor or outdoor location, moisture, poolside or coastal exposure, cleaning regime, surface-finish expectations, drainage, and crevice access.
• Commercial scope: drawing revision, quantities by type, left/right or corner variants, included loose accessories, spares, packaging, destination, and the inspection documents required with the order.
What this directory does not establish
• It does not certify a complete guardrail or glass-railing system, or confirm compliance for a specific jurisdiction, occupancy, load, or installation.
• It does not make every clamp, spigot, standoff, channel, bracket, adapter, or cap rail compatible with every glass panel, post, substrate, anchor, or adjacent component.
• It does not turn one product page or the category image into proof of the complete catalog, a fixed material grade, a tested performance value, or a project-specific supply package.
• It does not confirm that glass, posts, anchors, sealants, waterproofing, engineering, installation, or inspection are included unless the quotation explicitly lists them.
Prepare a useful glass-railing-hardware inquiry
Send any available drawing, glass schedule, hardware schedule, marked-up photo, or sample reference. Add panel dimensions and glass build-up; holes and notches; the intended support route; mounting position and substrate; adjacent posts, rails, or walls; environment and finish; quantities by type; required accessories; delivery destination; and the responsibility split for glass, anchors, waterproofing, engineering, and installation. If the design is still early, an annotated photo with rough dimensions is enough to begin routing the request, but final production inputs must be confirmed before an order is released.
Compare tube-only and component-package handrail quotes by separating fittings, fabrication, mounting interfaces, finish work and delivered quantities.
Compare continuous and sectional handrail supply using delivery access, joint locations, mating details and section identification before fabrication release.
Choose a handrail support change by comparing wall and post interfaces, preserving the gripping path and locating the transition on coordinated drawings.
Choose between level, raked, and raked-to-level mesh panel geometry by railing run, pattern orientation, interfaces, and project drawings.
应根据管子的实际内径、所需的固定强度以及安装空间,指定扶手套管和接头锁扣,以确保连接件能够安装到位并牢固固定。.
Locate splices with supports, transitions and assembly access so shipping breaks also work as documented connections in the installed handrail.


佛山伊桑金属制品有限公司自豪地保持着 CE 认证 (根据《建筑产品指令》(第 305/2011 号法规),我们获得了 TD32772401 认证(认证编号:TD32772401),这肯定了我们对欧洲最高安全和质量标准的承诺。
认证产品范围:
我们全面的栏杆配件组合--包括玻璃夹、张紧器、托架、墙面安装件、底座、扶手配件、电缆五金件和立柱组件--符合以下要求 EN1906:2012 标准,确保所有装置的结构完整性和性能可靠性。.
这对您的项目意味着什么?
✓ 完全符合欧洲和国际市场的法规要求
✓ 经独立验证的安全和耐用性能
✓ 为架构规范提供文档支持
✓ 由第三方提供质量保证,让您高枕无忧
认证有效期至 2027 年 | 测试报告:CE-FE24122001-CY

