墙壁安装支架

墙壁安装支架

Choose a wall bracket by interface, not by appearance

Wall-mount bracket selection starts with the finished wall condition and the handrail that must be held at a defined position. A compact bracket, an extended arm and an adjustable head create different leverage, access and alignment conditions. Use this category to choose the correct public product route, then match the exact wall plate, support head and fixing responsibility in the proposed configuration.

Discuss wall-bracket options on WhatsApp

Five current product routes

标准墙壁安装支架

Start here for a fixed, general wall-to-handrail connection when no special offset or field adjustment has been identified. “Standard” is a routing label, not a verified load rating.

重型壁挂支架

Use this route when the project has defined higher design actions or a more demanding support condition. Compare only configurations with stated dimensions and project-accepted evidence; the name alone does not prove capacity.

可调墙托架

Use when a documented angle, position or alignment adjustment is needed during installation. Confirm the adjustment direction, range, access and final locking method.

加长型壁挂支架

Use when wall finishes, obstructions or the required handrail position create extra offset. A longer arm increases leverage at the wall interface, so projection and support design must be reviewed together.

嵌入式壁挂支架

Use when the connection must be compact or visually close to the wall. Confirm recess or plate geometry, installation access and how the fixing is inspected or serviced.

The fields that change the correct bracket

Decision — Provide — Why it changes the result

Finished wall and supporting structure — Section or photo showing finish layers, cavity, backing and structural substrate — The visible wall surface may not be the load-receiving structure, and the bracket plate must be fixed to a suitable support.

Handrail interface — Profile, outside dimensions, orientation and desired support or saddle contact — A support head for round tube does not automatically fit a square, rectangular or custom profile.

Clearance and projection — Dimensioned distance from finished wall to the required handrail position — It determines arm geometry and the leverage transferred to the wall connection.

Route and adjustment — Plan/elevation, stair or ramp angle, fixed or adjustable requirement — It separates fixed, adjustable and extended-reach routes and defines the final locked position.

Plate and fixing access — Permitted plate envelope, visible-fastener preference and installation access — Compact or concealed details may reduce access for drilling, tightening and later inspection.

Environment and finish — Interior/exterior exposure, cleaning chemicals and required visual finish — The quotation should state the proposed material and finish for review rather than relying on a generic category label.

Keep the wall bracket and anchor decisions connected

A bracket photo cannot determine the anchor system. The wall plate hole pattern, bracket projection, bracket spacing, wall build-up, design actions, edge conditions and installation procedure form one interface. The project engineer and the selected anchor manufacturer should confirm the final anchoring design for the actual substrate. Ask the ESANG proposal to state the bracket-side holes and whether any loose fasteners are included or excluded.

For an accessible handrail or another code-governed route, provide the project’s required handrail position, clearance, continuity and support criteria. A bracket can be made or selected to provided geometry, but it does not by itself establish compliance for the installed handrail and wall assembly.

一份可比报价应包含哪些内容

• product route and a drawing or marked dimensions for the proposed bracket;

• wall plate, arm and handrail-support geometry, including clearance and projection;

• proposed material grade and finish, without implying every photographed form is available in every combination;

• adjustment and final locking details where an adjustable route is proposed;

• included parts, excluded anchors and the intended fixing or fabrication work;

• open inputs that must be closed before production.

You can begin with a wall photo, handrail profile, approximate dimensions and quantity. Mark uncertain fields instead of waiting for a finished drawing.

Send the wall and handrail details on WhatsApp

相关职位:

埃桑的项目

埃桑证书

佛山伊桑金属制品有限公司自豪地保持着 CE 认证 (根据《建筑产品指令》(第 305/2011 号法规),我们获得了 TD32772401 认证(认证编号:TD32772401),这肯定了我们对欧洲最高安全和质量标准的承诺。

认证产品范围:
我们全面的栏杆配件组合--包括玻璃夹、张紧器、托架、墙面安装件、底座、扶手配件、电缆五金件和立柱组件--符合以下要求 EN1906:2012 标准,确保所有装置的结构完整性和性能可靠性。.

这对您的项目意味着什么?

  • ✓ 完全符合欧洲和国际市场的法规要求

  • ✓ 经独立验证的安全和耐用性能

  • ✓ 为架构规范提供文档支持

  • ✓ 由第三方提供质量保证,让您高枕无忧

认证有效期至 2027 年 | 测试报告:CE-FE24122001-CY

埃桑的项目

立即联系我们 !