Postes de aço inoxidável

Postes de aço inoxidável

Choose a railing post by its job in the run before choosing its shape. Intermediate, terminal, corner and stair-transition positions can require different holes, brackets, infill terminations and base details even when the visible post profile is the same. This category routes current ESANG post subjects so buyers can build a clear post schedule rather than request one generic post for every position.

Discuss a post schedule on WhatsApp

Current post routes

Postes redondos de aço inoxidável

Start here when the hardware must wrap or align with a round face. State post diameter, every interface position and the required material grade rather than relying on appearance.

Postes quadrados de aço inoxidável

Start here for flat mounting faces and square-profile coordination. Face orientation matters when holes, clamps or brackets occur on more than one side.

Postes retangulares de aço inoxidável

Start here when the post has a directional face. Mark which dimension faces the railing run and which faces the opening.

Sistemas de postes intermediários

Use for repeated positions between ends and corners. Hole or bracket repetition, post spacing and field alignment drive the schedule.

Componentes de terminais de poste

Use at the start or end of a run. State what terminates there – rail, bar, rod, cable hardware or another component – and on which face.

Conjuntos de colunas de canto

Use where direction changes. Provide the plan angle and show how rails and infill approach the post from each side.

Sistemas de postes de corrimão

Use at stair starts, landings or prominent transitions. Stair pitch, handrail transition and the base condition must be coordinated together.

Representative post forms

Role first, profile second

Post decision — Show on the schedule — Why it changes the order

Intermediário — Repeated hole or bracket pattern, spacing and upper support. — A terminal fitting copied to an intermediate position can obstruct a continuous run.

Terminal — End-facing hardware, end clearance and the side from which installation is accessed. — End forces and visible finishing differ from pass-through positions.

Corner — Plan angle, incoming directions, corner rail detail and infill routing. — One-face drilling cannot simply be rotated if two runs meet with different interfaces.

Newel or transition — Stair pitch, landing elevation, handrail transition and base position. — The upper connection and visible height may change across a stair-to-landing transition.

Match every post interface

Profile and orientation

Round profiles require hardware shaped or adapted to a curved face. Square profiles provide flat faces but still need a defined face orientation. Rectangular posts add a long and short face, so the drawing must show which direction each post is installed. Do not approve a post from an elevation alone when side faces carry hardware.

Base and substrate

Pair the post body with the actual surface, fascia, core or custom mount. The quotation should identify the post-to-base connection and what base hardware is included. The project designer or engineer should define the installed loads, substrate capacity, edge distances and anchor requirements; a post photograph cannot answer those site questions.

Upper rail and infill

Mark the upper-rail support height, bracket or saddle type, and all infill interfaces. For bars or rods, specify pass-through versus stopped ends. For glass, identify the separate clamp or adapter route and glass build-up. For cable, provide the cable layout and distinguish pass-through, tensioning and terminal positions.

Material e acabamento

Request the material grade required by the project specification and exposure; grade cannot be confirmed from a photograph. State the finish and its direction on visible faces, plus any weld finishing or protective handling requirement. Ask the quotation to identify the proposed grade and finish rather than assuming the category title applies to every configuration.

What to send and what to compare

A marked-up layout with labels such as I1 (intermediate), T1 (terminal), C1 (corner) and N1 (newel/transition) is enough to begin. Add available heights, profile preferences, base condition, top-rail detail, infill type and estimated quantities.

For a like-for-like comparison, require the proposal to state:

• post role, profile, orientation, height and quantity by type;

• proposed material grade and visible finish;

• base or mounting interface included and any excluded anchors;

• holes, slots, welded tabs, inserts, brackets and removable fittings;

• upper-rail and infill interfaces by face;

• factory assembly, loose parts, packaging and drawing approval points.

Send your post layout on WhatsApp

Posts relacionados:

Projetos da Esang

Certificado da Esang

A Foshan ESANG Metal Products orgulhosamente mantém Certificação CE (Nº de verificação TD32772401) de acordo com a Diretiva de Produtos de Construção (Regulamento nº 305/2011), afirmando nosso compromisso com os mais altos padrões europeus de segurança e qualidade.

Certificado Linha de produtos:
Nosso abrangente portfólio de acessórios para guarda-corpos, incluindo braçadeiras de vidro, tensionadores, suportes, suportes de parede, sapatas de base, acessórios para corrimão, ferragens para cabos e componentes para postes, atende a EN1906:2012 garantindo a integridade estrutural e a confiabilidade do desempenho em todas as instalações.

O que isso significa para seu projeto:

  • Conformidade regulatória total para os mercados europeu e internacional

  • Desempenho de segurança e durabilidade verificado de forma independente

  • Suporte de documentação para especificações arquitetônicas

  • Tranquilidade com a garantia de qualidade de terceiros

Certificação válida até 2027 | Relatório de teste: CE-FE24122001-CY

Projetos da Esang

Entre em contato conosco agora!